Open Roads Forum

Print  |  Close
Page of 435  
Prev  |  Next

Topic: Avion truck campers - Hundreds of photos

Posted By: D1trout on 02/28/14 02:26pm

67, I am planning to vent the water tank. I know I need to do that. And I'll use plastic pipe, either PEX or the flexible vinyl tubing and fittings that are used in the pressure water systems in sailboats. My question is more about venting the drain side of the system. I'm only having a gray water tank and I'll drain that out into a bucket to dump in the woods most of the time. Plus I'm using those inline drain valves in lieu of P traps, to save space and add efficiency. If I can avoid the typical vent pipe thru the roof, I'd like to. And get the 4" of space inside in the bargain.

Are you using 6 volt batteries? They seem like a good solution. It appears the total usage for LEDs in my proposed system is just over 1 amp per day! Astonishing! It's the fridge that gets you. I just bought a Norcold that's 3 amps per hour, which is quite low on the scale of such things.

Such an interesting process!

Dick


Posted By: 69 Avion on 02/28/14 05:32pm

D1, I would recommend a 1-1/2" ABS vent off of your plumbing system to allow the system to drain properly, including the draining of your gray water tank.


Ford F-350 4x4 Diesel
1988 Avion Triple Axle Trailer
1969 Avion C-11 Camper


Posted By: D1trout on 02/28/14 08:43pm

69, thanks for your reply. It just seems reasonable to suppose that with a sink and a shower drain, I could address the pressure issue when draining the gray water tank without adding a vent pipe. I don't have the answer but will do some homework and report back here.
Dick


Posted By: 69 Avion on 02/28/14 08:44pm

D1trout wrote:

69, thanks for your reply. It just seems reasonable to suppose that with a sink and a shower drain, I could address the pressure issue when draining the gray water tank without adding a vent pipe. I don't have the answer but will do some homework and report back here.
Dick

Without the vent your sink will have a hard time draining. In fact, without a decent vent, your tank will have a hard time draining.


Posted By: D1trout on 02/28/14 08:45pm

By the way, 69, what sort of a battery set-up are you using? I know you've thought your entire system out with great care...
Dick


Posted By: ticki2 on 02/28/14 09:00pm

D1trout wrote:

69, thanks for your reply. It just seems reasonable to suppose that with a sink and a shower drain, I could address the pressure issue when draining the gray water tank without adding a vent pipe. I don't have the answer but will do some homework and report back here.
Dick


You will by sucking out the traps when you empty the tank .


'68 Avion C-11
'02 GMC DRW D/A flatbed


Posted By: D1trout on 02/28/14 09:09pm

Tiki2, I'm going to use the HepVo waterless trap for it's compact efficiency. It seem to me that it will act as a vent when water flows down a drain or out a gray water tank...?


Posted By: ticki2 on 03/01/14 04:46am

D1trout wrote:

Tiki2, I'm going to use the HepVo waterless trap for it's compact efficiency. It seem to me that it will act as a vent when water flows down a drain or out a gray water tank...?


Interesting product , it seems from their literature no additional vent would be required . Hope you will follow up with a report after putting it into service . Could be useful in an RV where they can sit for months at a time .


Posted By: 67avion on 03/01/14 08:59am

D1, we have a set of three 12V AGM batteries. I think I mentioned before that there was no grand theory involved. If anything it was the concept of brute strength in terms of electrical storage. Unfortunately, I didn't really calculate the amount of solar power needed for the batteries and whether I have the real estate to place them. It looks like I can do it, but just barely. So, if my camping style were to shift to long periods of dry camping I might have some problems. But, I would probably have some problems with water and waste storage as well.

I'm impressed by the HepVo as well. Let us all know how it works.


Posted By: Dodgeavion on 03/01/14 09:18am

I used a cheap drill from harbor freight as the insulation dust is rough on the drill. I also purchased plastic abrasive brushes from harbor freight to remove some insulation. Mostly I scraped with plastic putty knives. Wore out four of the knives. Used the brush and drill in hard to get places.


Print  |  Close
Page of 435  
Prev  |  Next