js503
Georgia
New Member
Joined: 09/04/2011
View Profile
Good Sam RV Club Member
 Offline
|
Hello all. We have a 2006 Monaco Monarch SE 30PPD with two slides. Recently when attempting to bring in slides, nothing worked. I checked everything I could but no luck. inally used piece of wire to "jump" them in. Motors worked fine during procedure. The slide out controller circuit board is made by IDS with part number 10667E. Could board be the problem? How can I check it to see if its the problem. Any and all help appreciated. Thanks, John
|
CA Traveler
The Western States
Senior Member
Joined: 01/03/2004
View Profile
Offline
|
Check to see if you have power to the board.
2009 Holiday Rambler 42 Scepter with ISL 400 Cummins
2004 Honda CR-V
Bob
|
-Gramps-
Portsmouth VA
Senior Member
Joined: 03/09/2005
View Profile
Good Sam RV Club Member
|
Does your engine have to be off for the slides to work?
___________________________________________
08 Holiday Rambler Vacationer 38PLT Workhorse UFO GAS Pusher Chassis
06 Saturn Vue toad, SMI Breaking sys,Blue Ox tow bar.
My FMCA Blog
|
Executive
California/Arizona/South Dakota
Senior Member
Joined: 02/07/2008
View Profile
Offline
|
Engine OFF, Air bags FULL, ALL BAY Doors CLOSED and EBrake SET...Also, your batteries must be reasonably charged....if you have a bad connection in one of the bay doors the slides won't work. Since you were able to "jump" them, I would think the board is ok. I would look at the pin connections on your bay doors first........Dennis
Dennis and Debi
Monaco Executive M-45PBQ Quad Slide
525HP Cummins ISM 6 Spd Allison
Chevy HHR W/ ReadyBrute
Full Timing and Living the Dream 
|
MartyAndPeg
North Florida for the Winter
Senior Member
Joined: 01/17/2002
View Profile
Offline
|
Not sure with your unit, but it possible there is a solenoid that prevents you from deploying the slides while the engine is running. If that is the case, and the solenoid is sticking, then try turning the ignition key to on, then back off. Either that or locate the solenoid and tap on it to free the contacts.
Marty & Peg & 2 cats
2005 Tiffin Phaeton 40QDH/350HP Cat/MH3000
2009 Ford F150 4x4/Brake Buddy
2011 Harley Softail Heritage/Rampage Motorcycle Lift
Full-Timing-10 years and counting!
Looking for a purpose in life, try Habitat for Humanity RV-Care-A-Vanners!
|
|
|
js503
Georgia
New Member
Joined: 09/04/2011
View Profile
Good Sam RV Club Member
Offline
|
Thanks for replies. All standard procedures for using slides were in place so this is not the problem. When I jumped the slides in, I had unpluggged the board connection and used power from light by removing bulb and using that electricity. My bay doors are not connected to the system, but they were closed at the time. The circuit board has relays but it is the older style that you cant pull one out to replace, newer ones you can. Anyone have any other suggestions? Thanks, John
|
John339
Clyde Ca. USA
Senior Member
Joined: 01/24/2002
View Profile
Offline
|
My neighbor has to have his drivers seat forward before the slide will come in.
It might not clear when his driving seat is rearward.
John and Cindy and Misty Rain and Senor Paco(Chihuahuas)
1994 Coachmen Catalina 300 MB RD
in sunny Clyde, Calif. KE6IDM
|
chastho
arkansas
Senior Member
Joined: 07/27/2005
View Profile
|
If your board has the small about one inch square relays that is probably your problem. They can be replaced. I had one go out, the slide would go out but not in. I bought the relays from Mouser electronics and with a soldering iron heated the solder holding the relay and removed it. Put the new one in and resoldered it.
|
deblas
So Cal
Full Member
Joined: 02/03/2009
View Profile
Offline
|
Is there one control board for both slides or independent control boards? The reason I ask is I just had a similar problem this morning with my living slide; with the slide in the extended position, it did nothing when trying to retract but it did click when attempting to extend. So I located control boards (living and bedroom) and after some checking with the voltmeter, it was looking like a bad board. As a last ditch effort, I unplugged the harness for the bedroom slide and plugged it into the living control board and the board worked properly....hmmm...so I plugged the living harness into the bedroom control board and it worked too!! So I put all harness' back to normal and all worked ok.
I guess it was a poor connection at the control board, man did I get lucky. Sorry for the wind.....
2003 Bounder 35E W22
|
slickest1
canada
Senior Member
Joined: 07/19/2010
View Profile
Good Sam RV Club Member
Offline
|
I had a problem with my slide and it turned out to be the switch itself. I thought it would be somthing more serious but that was all it was. Good luck.
2000 H.R. Imperial 38wds rr8r roadmaster, isc 350 cummins
2007 Chevy Trailblazer, Blue ox towbar
Ready Brake with breakaway.
|
|
|
